| Features |
|
 |
Perfect for smaller workshops
Designed for smaller workshops and other ‘short run' situations.
Pre glued edgings mean you're underway in just a few minutes.
An economical machine for edges from 0.4mm to 2.0mm.
|
 |
Big time savings
Compared to a hand-fed machine the fully auto V320 is around 4 times faster on thin and 6 to 8 times faster on thick edges.
Reduced labour increases profits.
|
|
Easy height setting
Reset feed track and top trimmer height using a single hand wheel.
Digital readout eliminates guesswork.
|
|
|
Long in-feed fence
800mm long solid 20 x 20mm in-feed fence guarantees perfect alignment.
‘Quick change’ overlay fence for virtually instant fence resetting for 0.4, 1mm and 2mm edges.
|
|
|
Clear access and the best feed
The complete feed unit swings forward out of your way for cleaning and set up.
Toothed rubber belt for non slip feed.
70mm wide with a full 1100mm feeding length.
|
 |
Lower power use, easy extraction
Air consumption is low with only 6.5 bars of pressure required.
Electrical draw just 4kw.
A 1hp extractor is all you need.
Single extraction connection point.
|
 |
Easy panel handing
400mm in and out-feed extension tables handle larger panels.
|
 |
Well supported panels
320mm ‘pull out' extension table in front.
|
|
Solid but compact
210 kg Solid construction e.g. the one piece welded frame.
But requires just 1990 x 920mm of floorspace including the tape coil holder.
|
 |
Easy tape setup
Rollers in the tape tray eliminate drag for trouble free tape feeding.
|
 |
Better tape guides
Large vertical guides.
Horizontal tape guides adjust on twin rods to maintain parallel.
Central height adjustment of the horizontal tape guides.
|
 |
Reliable tape feed
The panel directly contacts the tape drive roller in the bed of the table - not in the fence line as other do. This guarantees the tape feed without relying on the panel being hard up against the in feed fence.
|
 |
Reliable heat for superior adhesion
Swiss ‘Leister’ 3 kw heater proven in thousands of machines.
Clear readout of temp at the outlet nozzle.
Ease of service. Ceramic ‘plug in’ element with built in filter.
|
 |
No cold or damp worries
Panel pre-heat plate - eliminates problems with cold damp panels.
Simple ‘One to ten’ temperature setting from the front of the machine.
|
 |
Pressure where it counts
3 pressure rollers guarantee much stronger bonding than single roller systems.
Positioned to ensure correct cooling of the glue before trimming.
|
 |
Keeping up the pressure
5 'angled' sets of table rollers guarantee your panels stay against the fenceline.
|
 |
Flush end trim, everytime
Twin ‘front and rear’ knives travel with the panel during the cut.
Trimming reference point is the panel itself - flush every time.
Reliable pneumatic action.
Guide rollersensure the panel won’t be deflected off line.
|
|
Perfect top and bottom too
High speed cutter blocks with 4 TCT replaceable knives.
The key to high quality trimming results.
A single large motor so power is always directed where tape overhang is greatest.
Flat belt drive eliminates motor ‘hum’ transferring to the cutters.
|
 |
Up and down - without scuffing
Trimmers follow the panel surface via large rotary rollers so any panel bowing won't affect the trim quality.
Rotating trace rollers mean delicate panels are not scuffed or marked as they are by fixed bars.
|
 |
Resetting made easy
Digital readouts on each trimmer take the guesswork out of resetting from thick to thin tape – and back again
|
 |
Safe too
Unused heat properly vented. Electric are fully dust sealed.
Lockable main switch - no unauthorized use.
All tools required for setting included. Safety Interlock on feed track.
Fully guarded but you can safely see what's happening.
Quiet induction motors. Total noise just 71.5 decibels.
Built to the toughest ‘CE' safety standards.
|
 |
You have the room
|
 |
A name you can rely on
The world's most successful preglue Edgebanders.
10-year track record in Europe and USA.
Over 100 Casadei machines in NZ workshops.
Invest in Casadei with 100% confidence
|
Download a feature benefit report for the V320 >>
